• Home
  • Download PDF
  • Order CD-ROM
  • Order in Print
Figure 2-8. Fuel tank, muffler, spark plug, cylinder head, and governor control assembly, model OEG-458-ENG-1 and OEG-458-ENG-2, removed points.
Section V. OPERATION UNDER UNUSUAL CONDITIONS - TM-5-4310-227-150038

TM-5-4310-227-15 Compressor Reciprocating: Air; Gasoline Engine 15 CFM 175 PSI; Receiver Mounted (Champion Pneumatic Model OEG-458-ENG-1) Manual
Page Navigation
  19    20    21    22    23  24  25    26    27    28    29  
TM 5-4310-227-15
Callouts FOr Figure 2-8-Continued.
28  Throttle shaft swivel block
6
Leather liner (2 rqr)
29  Nipple, pipe, 1-11 1/2 X 3 in.
7
Chain
30  Muffler
8
Fuel tank cap
31  Screw, cap, hex-hd, 3/8-16 X 1 1/2 in. (3 rqr)
9
Fuel tank
32  Cylinder head
10
Fuel tank strap (2 rqr)
33  Screw, cap, hex-hd, 3/8-16 X 1 1/4 in. (2 rqr)
11
Screw, mach, pan-hd, 1/4-20 1 3/4 in. (2 rqr)
34  Washer, lock, 1/4 in. (4 rqr)
12
Washer, lock, 1/4 in. (2 rqr)
35  Screw, mach. 1/4-20 X 3/8 in. (4 rqr)
13
Nut, plain, hex, 1/4-20 (2 rqr)
36  Air shroud
14
Fuel tank bracket
37  Pin, cotter, 1/16 X 1 in.
15
Adjusting lever
16
38  Compression spring
Screw, cap, hex-hd, 3/8-16 X 1 in. (2 rqr)
17
Washer, lock, 3/i in. (2 rqr)
39  Control bracket
18
40  Spring adjusting screw
Control bracket brace
19
Cylinder and crankcase Ay.
41  Nut, plain, hex, 10-32 (2 rqr)
Drive pulley end plate
20
42  Washer, flat, 0.88 in. id, 0.375 in. od, 0.049
21
Washer, lock, 3/8 in. (4 rqr)
in. thk
22
Screw, cap, hex-hd, 3/8-16 X 1 in. (4 rqr)
43  Nut, plain, hex, 1/4-28
23
support bracket
44  Extension spring
24
Screw, cap, hex-hd, 1/4-20 X 3/4 in. (2 rqr)
45  Swivel block
25
Governor control lever
46  Washer, flat, 1/4 in.
26
Pin, cotter, 3/64 X 3/8 in.
47  Pin, stralght, threaded, 1/4-20 X 1 5/16 in.
27
Control rod
Section IV. OPERATION UNDER USUAL CONDITIONS
(2) Open the fuel shutoff valve (3, fig.
2-25. General
2-4).
a. The instructions in this section are for the
(3) Move the choke lever (31, fig. 2-7)
information and guidance of the personnel re-
to the CL (closed) position.
sponsible for the operation of the air compres-
sor.
(4) Close the globe valve (5, fig. 2-3).
b. It is essential that the operator know
(5) Open the air receiver tank draincock
how to perform every operation of which the
(4, fig. 1-4).
air compressor is capable. This section gives in-
(6) Wind the engine starter rope around
structions on starting and stopping the air com-
starting pulley assembly (29, fig. 2-
pressor, on the basic motions of the air com-
7), and with a quick, steady pull,
pressor, and on co-ordinating the basic motions
start the engine.
to perform the specific tasks for which the
(7) Allow the engine to run for several
equipment is designed. Since nearly every job
minutes; gradually open the choke
presents a different problem, the operator may
lever until the engine is warmed up
have to vary the given procedure to fit the in-
and running smoothly.
dividual job.
(8) Close the air receiver tank draincock.
2-26. Starting
(9) As the air compressor operates, the
air pressure gage (6, fig. 1-1) will
OEG-458-
a. Model
OEG-458-ENG-1,
indicate the amount of pressure in the
ENG-2, and OEG-459-ENG-3.
receiver tank. Check the gage fre-
(1) Perform the applicable daily services
quently so that the compressor may be
(para 3-8).
shut down when the desired pressure
Note. For cold weather starting, refer to
has been reached.
paragraph 2-23.
2-13






Western Governors University

Privacy Statement
Press Release
Contact

© Copyright Integrated Publishing, Inc.. All Rights Reserved. Design by Strategico.