TM 5-4310-250-24P
f.
QTY (Column (6)). The QTY (quantity per figure
column) indicates the quantity of the item used in the
breakout shown on the illustration figure, which is
prepared for a functional group, subfunctional group, or
an assembly. A "V" appearing in this column in lieu of a
quantity indicates that the quantity is variable and the
quantity may vary from application to application.
4. Explanation of Columns (Section IV).
a.
NATIONAL STOCK NUMBER (NSN) INDEX.
(1)
STOCK NUMBER column. This column
lists the NSN by National item identification number
(NIIN) sequence. The NIIN consists of the last nine
NSN
digits of the NSN (i.e., 5305-01-674-1467.) When using
NIIN
this column to locate an item, ignore the first 4 digits of
the NSN. However, the complete NSN should be used
when ordering items by stock number.
(2)
FIG. column. This column lists the
number of the figure where the item is identified/located.
The figures are in numerical order in Section II and
Section III.
(3)
ITEM column. The item number identifies
the item associated with the figure listed in the adjacent
FIG. column. This item is also identified by the NSN
listed on the same line.
b.
PART NUMBER INDEX. Part numbers in this
index
are
listed
by
part
number
in
ascending
alphanumeric sequence (i.e., vertical arrangement of
letter and number combination which places the first
letter or digit of each group in order A through Z,
followed by the numbers 0 through 9 and each following
letter or digit in like order.)
(1)
FSCM column. The Federal Supply Code
for Manufacturer (FSCM) is a 5 digit numeric code used
to identify the -manufacturer, distributor, or Government
agency, etc., that supplies the item.
(2)
PART NUMBER column. Indicates the
primary number used by the manufacturer (individual,
firm, corporation, or Government activity), which controls
the design and characteristics of the item by means of its
engineering drawings, specifications standards, and
inspection requirements to identify an item or range of
items.
(3)
STOCK NUMBER column. This column
lists the NSN for the associated part number and
manufacturer identified in the PART NUMBER and
FSCM columns to the left.
(4)
FIG. column. This column lists the
number of the figure where the item is identified/located
in Section II and III.
(5)
ITEM column. The item number is that
number assigned to the item as it appears in the figure
referenced in the adjacent figure number column.
c.
FIGURE AND ITEM NUMBER INDEX.
(1)
FIG. column. This column lists the
number of the figure where the item is identified/located
in Section II and III.
(2)
ITEM column. The item number is that
number assigned to the item as it appears in the figure
referenced in the adjacent figure number column.
(3)
STOCK NUMBER column. This column
lists the NSN for the item.
(4)
FSCM column. The Federal Supply Code
for Manufacturer (FSCM) is a 5-digit numeric code used
to identify the manufacturer, distributor, or Government
agency, etc., that supplies the item.
(5)
PART NUMBER column. Indicates the
primary number used by the manufacturer (individual,
firm, corporation, or Government activity), which controls
the design and characteristics of the item by means of its
engineering drawings, specifications standards, and
inspection requirements to identify an item or range of
items.
5. Special Information.
Use the following subparagraphs as applicable:
a.
USABLE ON CODE. The usable on code
appears in the lower left comer of the Description
column heading. Usable on codes are shown as
"UOC........ in the Description Column (justified left) on
the
first
line
following
applicable
item
description/nomenclature. Uncoded items are applicable
to all models. Identification of the usable on codes used
in the RPSTL are:
Code
Use On
AZM
M250RPV
AZN
6M250RPV
BYY
9M250RPV
b.
FABRICATION
INSTRUCTIONS.
Bulk
materials required to manufacture items are listed in the
Bulk Material Functional Group of this RPSTL. Part
numbers for bulk materials are also referenced in the
description column of the line item entry for the item to
be
manufactured/fabricated.
Detailed
fabrication
instructions for items source coded to be manufactured
or fabricated are found in TM 5-4310-250-15.
4