TM 5-4930-207-20P
the item. Items that are included in kits and sets
Recoverability
are listed below the name of the kit or set, with the
Definition
Code
quantity of each item in the kit or set indicated in
Nonreparable
item.
When
z
the quantity incorporated in unit column. When
unserviceable, condemn and dispose at
the part to be used differs between serial numbers
the level indicated in position 3.
of the same model, the effective serial numbers are
o
Reparable item. When uneconomically
shown as the last line of the description. In the
reparable, condemn and dispose at
Special Tools List, the initial basis of issue (BOI)
organizational level.
appears as the last line in the entry for each special
tool, special TMDE, and other special support
F
Reparable item. When uneconomically
equipment. When density of equipments sup-
reparable, condemn and dispose at the
ported exceeds density spread indicated in the
direct support level.
basis of issue, the total authorization is increased
H
Reparable item. When uneconomically
accordingly.
reparable, condemn and dispose at the
g. Unit of Measure (U/M). Indicates the stan-
general support level.
dard of the basic quantity of the listed item as used
D
Reparable item. When beyond lower
in performing the actual maintenance function.
level repair capability, return to depot.
This measure is expressed by a two-character
C o n d e m n a t i o n and disposal not
alphabetical abbreviation (e.g., ea, in., pr, etc.).
authorized below depot level.
When the unit of measure differs from the unit of
L
Reparable item. Repair, condemnation,
issue, the lowest unit of issue that will satisfy the
and disposal not authorized below
required units of measure will be requisitioned.
depot/specialized repair activity level.
h. Quantity Incorporated in Unit. Indicates the
A
Item requires special handling or
quantity of the item used in the breakout shown on
condemnation procedures because of
the illustration figure, which is prepared for a
specific reasons (i.e., precious metal con-
functional group, subfunctional group, or an
tent, high dollar value, critical material
assembly, A "V" appearing in this column in lieu
or hazardous material). Refer to ap-
of a quantity indicates that no specific quantity is
p r o p r i a t e manuals/directives for
applicable (e.g., shims, spacers, etc.).
specific instructions,
4. Special Information.
c. National Stock Number. Indicates the Na-
tional stock number assigned to the item and
a. Repair parts kits and gasket sets appear as
which will be used for requisitioning purposes.
the last entries in the repair parts listing for the
figure in which its parts are listed as repair parts.
d. Part Number. Indicates the primary number
used by the manufacturer which controls the
b. The following publications pertain to
design and characteristics of the item by means of
lubricating and servicing unit, and its components:
its engineering drawings, specifications standards,
TM 5-2805-203-14
Organizational, DS and GS
and inspection requirements to identify an item or
Maintenance Manual
range of items.
TM 5-2805-203-24P Organizational, DS and GS
NOTE
Maintenance Repair Parts
When a stock numbered item is requisi-
and Special Tools Lists
tioned, the repair part received may
TM 5-4930-207-12
Operator and Organizational
have a different part number than the
Maintenance Manual
part being replaced.
e. Federal Supply Code for Manufacturer
c. The illustrations in this manual are identical
(FSCM). The FSCM is a 5-digit numeric code listed
to the applicable illustrations published in the
in SB 708-42 which is used to identify the manufac-
-34P Direct and General Support and Depot
turer, distributor, or Government agency, etc.
Maintenance Repair Parts and Special Tools List
manual, and the figure numbers are the same as
f. Description. Indicates the Federal item name
appear in that manual. The -34P illustrations are
and, if required, a minimum description to identify
3
