• Home
  • Download PDF
  • Order CD-ROM
  • Order in Print
Removal of Protective Material and Devices
Figure 2-2, Instrument panel, models BMW-452-ENG and BMW-452-ENG-1.

TM-5-4310-227-15 Compressor Reciprocating: Air; Gasoline Engine 15 CFM 175 PSI; Receiver Mounted (Champion Pneumatic Model OEG-458-ENG-1) Manual
Page Navigation
  10    11    12    13    14  15  16    17    18    19    20  
TM 5-4310-227-15
b. Pay particular attention to receiver tank
2-9. Servicing Used Equipment
mounting platform, air cleaner, and pres-
sure gage.
Perform the procedures described in para-
C . Carefully inspect the fuel tank, fuel filter
g r a p h 26. Clean the exterior of the unit
assembly, gasoline engine, and unloader valve.
thoroughly. Coat the exposed metal surfaces
Inspect for fuel, oil, or air leaks.
with a film of oil or grease. Correct all de-
d. Correct or report all deficiencies to organ-
ficiencies or report them to organizational
izational maintenance.
maintenance.
Section Il.
MOVEMENT TO A NEW WORKSITE
(4) Attach the air compressor to the tow-
2-10. Dismantling For Movement
ing vehicle and tow the unit to the
a. Model
OEG-458-ENG-1,
OEG-458-
new worksite.
ENG-2, and OEG-458-ENG-3.
c. Model BMW-452-ENG-1.
(1) Stop the air compressor (para 2-27).
(1) Stop the air compressor (para 2-27).
(2) Remove the hose assembly (para 3-
(2) Remove the hose assembly (para 3-
88).
88), and place it in the stored posi-
tion.
(3) Remove the mounting hardware that
(3) Close and latch all doors.
s e c u r e s the air compressor to the
(4) Remove the mounting hardware that
mounting base.
s e c u r e s the air compressor to the
(4) Lift the air compressor onto the car-
mounting base.
rier with a lifting device of at least
(5) L.ift the air compressor onto the car-
800-pound capacity and move the air
rier with a lifting device of at least
compressor to the new worksite.
1,000 pound capacity and move the
b. Model BMW-452-ENG.
air compressor to the new worksite.
(1) Stop the air compressor (para 2-27).
2-11. Reinstallation After Movement
(2) Remove the hose assembly (para 3-
88), and place it in the stored posi-
a. Install the hose assembly (para 3-88).
tion.
b. Install the air compressor at the new
worksite (para 27).
(3) Close and latch all doors.
Section Ill. CONTROLS AND INSTRUMENTS
amount of air pressure in the tank. The gage
2 - 1 2 . General
will read to 300 psi but normally will range
This section describes, locates, and furnishes
between 0 to 175 psi.
the operator with sufficient information per-
b. The air pressure gage for models BMW-
taining to the various controls and instruments
452ENG and BMW-452-ENG-1 is located on
provided for the proper operation of the air
the instrument panel (7, fig. 2-2).
compressor.
2-14. Fuel Gage
2-13. Air Pressure Gage
The fuel gage (8, fig. 2-2), models BMW-
a. The air pressure gage (6, fig. 11), mod-
4 5 2 - E N G and BMW-452-ENG-1, mounted
e l OEG-458-ENG-1 and OEG-458-ENG-2,
on the instrument panel, indicates the amount
a n d (6, fig. 13) model OEG-458-ENG-3
of fuel in the fuel tank.
mounted on the air receiver tank, indicates the
2-3






Western Governors University

Privacy Statement
Press Release
Contact

© Copyright Integrated Publishing, Inc.. All Rights Reserved. Design by Strategico.