TM 5-4310-227-34P
erence number, or part number is known
assembly at a level higher than that
authorized for installation will indicate in
a n d the repair part is not illustrated:
the source column the higher level.
(1) Using the Index of Federal Stock
c. The following publications pertain to
N u m b e r s , Reference Numbers, or Part
Numbers find the pertinent Federal stock
the air compressor and its components:
number, reference number, or part num-
LO 5-2805-203-12
Lubrication Order
ber. Parts which are not illustrated will
LO 5-4310-227-15
Lubrication Order
r e f e r e n c e to a figure number but will
Organizational, DS and GS
TM 5-2805-203-14
not show an item number. This section
Maintenance Manual
is in ascending FSN sequence followed
TM 5-2805-203-24P Organizational, DS and GS
Repair Parts and Special
b y a list of reference numbers or part
Tools List
numbers in alpha-numeric sequence, cross-
Organizational, DS, GS, and
TM 5-4310-227-15
-referenced to the figures.
Depot Maintenance Manual
(2) Using the Table of Contents, locate
the figure number and page number.
5. How to Locate Repair Parts
(3) Using the applicable figure and
page number, locate the pertinent FSN,
a. When Federal stock number, ref-
reference number, or part number in the
e r e n c e number, or part number is un-
repair parts listing.
known:
(1) Using the table of contents, deter-
mine the assembly group within which the
6. Abbreviations
r e p a i r part belongs. This is necessary
Explanation
Abbreviation
s i n c e illustrations are prepared for as-
AWG . . . . . . . American Wire Gage
sembly groups, and listings are divided
cl . . . . . . . . . coil
into the same groups.
dia . . . . . . diameter
(2) Find the illustration covering the
ea . . . . . . . . . each
assembly group to which the repair part
ft . . . . . . . . foot (feet)
gl . . . . . . . . .gallon (s)
belongs.
id . . . . . . inside diameter
( 3 ) Identify the repair part on the
in . . . . . . . . . inch (es)
illustration and note the illustration figure
lh . . . . . . . . .left hand
n u m b e r and item number of the repair
lg . . . . . . . l o n g (length)
part.
mtg
.
.
.
mounting
no . . . . . . . . . number
(4) Using the repair parts listing, find
od . . . . . . . o u t s i d e d i a m e t e r
the assembly group to which the repair
rh . . . . . . . . right hand
p a r t belongs and locate the illustration
sh . . . . . . . . sheet (s)
figure and item number noted on the il-
tad . . . . . . . . thread (s) (cd)
lustration.
thk . . . . . . . . . . . . . . thick (ness)
w . . . . . . . . .wide (width)
b. When the Federal stock number, ref-
w/ . . . . . . .. with
erence number, or part number is known:
(1) Using the Index of Federal Stock
Numbers, Reference Numbers, and/or Part
7. Federal Supply Codes for Manufacturers
Numbers find the pertinent Federal stock
Code
Manufacturer
number, r e f e r e n c e number, and/or part
00000 . . . . . .
Ordnance Corps
number. This index is in ascending FSN
Amp. Inc.
00779 . . . . . . . .
sequence followed by a list of reference
Weatherhead Co., The
04255 . . . . . .
n u m b e r s or part numbers in ascending
True-Flate
Div.
08070 . . . . . .
alpha-numeric sequence, cross-referenced
Military Standards
08288 . . . .
to the illustration figure number and item
Allis-Chalmers Mfg. Co.
09367 . . . . . .
Szemco Inc.
10137 . . . . . .
number.
Champion Pneumatic Machinery Co.
11568 . . . . . .
(2) Using the repair parts listing, find
Crane Co.
14959 . . . . . .
the assembly group of the repair part and
Prestolite Co., The
19728 . . . . . .
the illustration figure number and item
Goodrich, B.F. Co., The
25472 . . . . . .
number referenced in the Index of Federal
Grinnell Co., Inc.
26403 . . . . . .
Imperial-Eastman Corp.
30327 . . . . . .
S t o c k Numbers, Reference Numbers, or
Independent Lock Co.
30399 . . . . . .
P a r t Numbers.
Pressed Steel Tank Co.
48816 . . . . . .
c. When the Federal stock number, ref-
Stewart-Warner Corp.
57733. . . . . .
v
