• Home
  • Download PDF
  • Order CD-ROM
  • Order in Print
Reassembly - TM-5-4310-354-140198
Figure 6-10. Compressor non-drive end, disassembly, blade inspection, and reassembly

TM-5-4310-354-14 Compressor Rotary; Air Skid Mounted; Diesel Engine 125 CFM 100 PSIG (Davey Model 6M125) Manual
Page Navigation
  183    184    185    186    187  188  189    190    191    192    193  
TM 5-4310-354-14
assemble the oil seal sleeve (70) on the
(20) with cap screw (15) and lock nut (14).
shaft. Install o-ring (69) on sealing sleeve
Pin (17) is used to attach speed control
(68) and assemble sealing sleeve (68)
arm to clamp (16).
over oil seal sleeve (70).
(14) Insert spring (12) into intake valve (13)
(8) Press oil seal (67) into bearing cover (65)
and assemble valve (13) into housing
with sealing lip of oil seal facing the oil
(32). Assemble stem (9) through cylinder
seal sleeve (70).  Assemble gasket (66)
(10), assemble spring (8), piston (7), and
and bearing cover (65).  Attach with six
attach together by assembling lock nut (6)
lock washers (64) and six cap screws
on stem (9).
(63).
(15) Press breather (4) into cover (3). Apply a
(9) Assemble the inner grip springs (57),
light coating of petroleum jelly on gasket
place coupling key (58) in shaft keyway,
(11) to hold in place against housing (32).
assemble drive coupling (56), outer grip
Assemble  gasket  (11),  cylinder  (10),
springs (57), retainer (55), lock washer
diaphragm (5), and cover (3).  Attach to
(54), and cap screw (53).
housing (32) with six lock washers (2) and
six cap screws (1).
(10) If removed, install pipe plug (52) in intake
end cover (49).  Assemble bearing outer
e. Installation. Install the air compressor assembly
race (51) in end cover (49).  Apply light
(para 5-11).
coating of petroleum jelly on o-ring (50)
and install o-ring (50) on the stator (93)
6-12.  Air Compressor Rotor Blade Inspection and
end flange. Assemble end cover (49) to
Replacement.
stator and attach with six seal washers
(48), five cap screws (47) and one cap
a. Disassembly.
screw (46). Assemble retainer (45) to end
of rotor shaft (84) with lock washer (44)
(1) Remove the hose reel assembly (para
and cap screw (43).  Assemble gasket
4-25).
(42) and bearing cover (41) onto end
cover (49) with six lock washers (40) and
(2) Remove the compressor access panel
six cap screws (39).
from the housing rear end panel.
(11) If removed, install two pipe plu gs (38) in
(3) Unhook the speed control rod return
intake housing (32). Assemble steel ball
spring. Remove the lock nut that secures
(37), spring (36), o-ring (35), and plug (34)
speed control rod stop block to control
into housing (32). Apply a light coating of
lever arm and remove the stop block from
petroleum  jelly  on  gasket  (33)  and
the lever arm.
assemble gasket (33) and intake housing
(32) onto end cover (49).  Attach with
(4) Disconnect  the
compressor
unloader
three lock washers (31) and three cap
control cable.
screws (30).
(5) Loosen
hose
clamp
and
remove
(12) If  removed,  install
stop  pin  (29).
compressor air intake flexible metal hose
Assemble shaft (28) in
housing (32) and
from the compressor.
attach valve plate (27)
to shaft (28) with
two lock washers (26)
and two screws
(6) Disconnect
hose
assemblies
from
(25).
compressor intake control housing.
(13) Assemble o-ring (23) and bushing (22) in
(7) Disassemble the compressor non-drive
bore of guide (20). Assemble gasket (21)
end in the numerical sequence shown in
and guide (20) onto housing (32) with two
figure 6-10 as follows:
lock washers (19) and two cap screws
(18). Insert push rod (24) in center hole of
guide (20). Attach clamp (16) to guide
6-19






Western Governors University

Privacy Statement
Press Release
Contact

© Copyright Integrated Publishing, Inc.. All Rights Reserved. Design by Strategico.