TM 5-4310-241-35P
(3) Determination of the total quantity of
(3) Recoverability code, indicates whether
unserviceable items should be returned for re-
parts required for maintenance of more than 100
covery or salvage. Items not coded are expend-
of these equipments can be accomplished by con-
able. Recoverability codes are:
verting the equipment quantity to a decimal fac-
tor by placing a decimal point before the next to
Code
Explanation
last digit of the number to indicate hundredths,
R
Applied to repair parts and assemblies which
and multiplying the decimal factor by the parts
are economically repairable at DSU and GSU
quantity authorized in the 51-100 allowance col-
activities and normally are furnished by sup-
ply on an exchange basis.
umn. Example, authorized allowance for 51-100
T
Applied to high dollar value recoverable repair
equipments is 40; for 150 equipments multiply 40
parts which are subject to special handling
by 1.50 or 60 parts required.
and are issued on an exchange basis. Such
h. One-Year Allowances Per 100 Equipments/
repair parts normally are repaired or over-
Contingency Planning Purposes, Column (9).
hauled at depot maintenance activities.
u
This column indicates the quantity required for
Applied to repair parts specifically selected for
salvage by reclamation units because of pre-
distribution and contingency planning purposes.
cious metal content, critical materials, high
The range of items indicates total quantities of
dollar value reusable casings or castings.
all authorized items required to provide for ade-
(4) This column also lists, below the SMR
quate support of 100 equipments for one year.
code, an index number for each item in ascend-
i. Depot Maintenance Allowance Per 100
ing numerical sequence, which is used to locate
Equipments, Column (10). This column indicates
items in the publication when the Federal stock
the quantity authorized for depot maintenance of
number and/or reference number is known.
100 equipments. Items authorized for use but not
b. Federal Stock Number, Column (2). This
for initial stockage are identified with an aster-
column indicates the Federal stock number for
isk in the allowance column.
j. Illustration, Column (11).
the item.
(1) Figure number. Indicates the figure
c. Description, Column (3). This column indi-
number of the illustration in which the item is
cates the Federal item name and any additional
shown.
description of the item required. A part number
(2) Item number. Indicates the callout num-
or other reference number is followed by the ap-
ber used to reference the item in the illustration.
plicable five-digit Federal supply code for man-
ufacturers in parentheses. Material required for
manufacture or fabrication is identified.
d. Unit of Issue, Column (4). This column in-
a. Identifications of the usable on codes of this
dicates the unit used as basis for issue, e.g., ea,
publication are:
pr, ft, yd, etc.
Used on
Code
e. Quantitv Incorporated in Unit Pack, Column
A ---- Compressor, model LP-512-ENG, Gasoline
(5). This column indicates the actual quantity
driven
B ---- Compressor, model OEH-34-60-ENG-1, Electric
contained in the unit pack.
motor driven
f. Quantity Incorporated in Unit, Column (6).
C ---- Compressor, model OEH-3440-ENG-2, Electric
This column indicates the quantity of the item
motor driven
used in the functional group.
D... Compressor, model OEH-34-60-ENG-3, Electric
motor driven
g. Thirty-Day DS/GS Maintenance Allow-
E ---- Compressor, model OEH-34-60-ENG-4, Electric
ances, Columns (7) and (8).
motor driven
(1) The allowance columns are divided into
F ____ Compressor, model LP-512-ENG-1, Gasoline
driven
three subcolumns. Indicated in each subcolumn is
Repair parts not symbolized applicable all models.
the quantity of items authorized for the number
Refer to TM 5-2805-206-24P for information on repair
of equipments supported. Items authorized for
parts and allowances for the MIL STD ENGINE EA08-1
use as required but not for initial stockage are
and 1A08-2.
b. Repair parts mortality has been based on
identified with an asterisk in the allowance col-
1,000 hours of operation per year.
umn.
(2) The quantitative allowances for DS/GS
c. Parts which require manufacture or assem-
levels of maintenance will represent initial stock-
bly at a category higher than that authorized for
installation will indicate in the source column the
age for a 30-day period for the number of equip-
higher category.
ments supported.
