TM 5-4310-335-14
(4)
Inspect gages for cracks or discolored glass.
(5)
Inspect flexible shaft for scoring.
(6)
Inspect service hose for fraying or wear.
(7)
Inspect all threaded parts for defective or damaged threads.
(8)
Repair any damage or replace parts which obstruct moving parts or could cause damage to the
equipment.
e. Repair.
(1) Remove dents and scratches from metal parts; weld minor breaks and cracks (roof mounting
brackets, etc.).
(2) Replace damaged or defective parts as necessary.
f. Assembly.
(1) Roof Assembly Components.
(147), elbow (148), tubing locknut (149), elbow (150) and unloader valve (151) on roof (152).
(b) Install locknut (137), flatwasher (138), fillister head machine screw (139), flat- washer (140),
cushioned clamps (141 and 142) and tie wrap (143).
(c) Install locknut (131), flatwasher (132), screw (133), flatwashers (134 and 135) and cushioned
clamp (136).
(d) Install locknut (125), flatwasher (126), fillister head machine screw (127), flat- washers (128
and 129) and cushioned clamp (130).
(e) Install shut-off valve (124).
(f) Install gage connector (122) and 0-5000 gage (123).
(g) Install shut-off valve (121).
(h) Install gage connector (119) and 0-4000 gage (120).
(i) Install locknut (114), washer (115), fillister head machine screws (116), washer (117) and
timer box assembly (118.
(j) Install protector gage (112) and 0-600 gage (113).
(k) Install bulkhead nut (106), washer (107 and 108), outlet fitting (109), adapter coupling (110)
and dust cap (111).
(l) Install plug (104) and preformed packing (105).
(m) Install locknuts (95), flatwashers (96), hex head machine bolts (97), flatwashers (98), hex
head machine bolts (99), lockwashers (100), flatwashers (101) and regulator brackets (102
and (103).
(n) Install bulkhead elbow (82), hex bulk- head nut (83), backup ring (84), preformed packing
(85), bulkhead tee (86), hex bulkhead nut (87), backup ring (88), preformed packing (89),
bulkhead elbow (90), hex bulkhead nut (91), backup ring (92), preformed packing (93) and
regulator (94).
(o) Install tube clamps where removed, remove tags and connect all air lines and fittings.
(p) Install locknuts (75), flatwashers (76 and 77), hex head machine screws (78), flat- washers
(79) and tank straps (80) securing fuel tank assembly (81).
(q) Install locknuts (70), flatwashers (71 and 72), hex head machine screws (73) and flat-
washers
(74).
(r) Install elbow fitting (69).
(s) Install locknut (58), flatwashers (59), fillister head machine screws (60), flatwashers (61),
locknuts (62), flatwashers (63), binder head machine screws (64), flatwashers (65) and tray
brackets (66 and 67) freeing tray (68).
(t) Install locknuts (64), flatwashers (55), fillister head machine screws (56) and flatwashers
(57).
(u) Install nipple (45), filter (46), nipple (47), tube (48), back pressure valve assembly (49),
preformed packing (50), check valve assembly (51), tube (52), and cross (53).
(v) Install locknut (40), flatwasher (41), binder head machine screw (42), flatwasher (43) and
cushioned clamp (44).
(w) Install locknut (34), flatwashers (35 and 36), binder head machine screw (37), flat- washers
(38) and cushioned clamp (39).
(x) Install locknuts (29), flatwashers (30), screws (31), and flatwashers (32) freeing hinge (33).
(y) Install latches (23), locknuts (24), flatwashers (25 and 26) and screws (27) freeing door (28).
(z) Install identification plates (14 through 22) if they were removed.
(aa) Install pads (13).
(ab) Install round head rivet (10), pop rivet washer (11) and instruction plate (12).
(ac) Install round head rivet (7), pop rivet washer (8) and schematic plate (9).
(ad) Install round head rivet (4), pop rivet washer (5) and instruction plate (6).
(ae) Install round head rivet (1), pop rivet washer (2) and warming plate (3).
(2) Fuel Tank Assembly.
6-9
