TM 5-4310-276-14
with roll pins (15) and cotter pine (14).
(2) Remove cotter pins (14), roll pins (15), axle
(3) Attach handles (13), leg (12), gusset (11),
(16), screws (17), nuts (18), LH nose (19) and RH
screws (10), nuts (9), gusset (8) and screws (4, 5, 6,
nose (20).
7). Attach feet (2) with screws (3) and nuts (1).
(3) Remove screws and bumper (21). Remove
(4) Assemble hubs (15, fig. 4-20), roller bear-
screws and nuts (22), rails (23) and crossmembers
ings (14), bearing retainers (13), bearing seals (12)
(24).
and end caps (11).
c. Cleaning and Inspection of Handtruck.
(5) Assemble tires (10), tubes (9), wheel disc
rear half (8), wheel dsic front half (7), capscrews
(6), hub bolts (5), nuts (4), washers (3) and nuts (2).
Drycleaning solvent, P-D-680, used to
Attach to axle with cotter pins (1). Service tires to
clean parts is potentially dangerous to
25 psi (1.766 kg/sq cm).
personnel and property. Avoid re-
e. Installiation.
peated and prolonged skin contact.
(1) Attach air receiver tank to handtruck
Do not use near open flame or exces-
with nuts and bolts.
sive heat. Flash point of solvent is
(2) Attach fuel tank with brackets, hangers
100F (38C).
and nuts. Attach fuel line to fuel tank.
(1) Wash all parts with cleaning solvent, item
(3) Attach compressor to handtruck.
5, App. D, and dry thoroughly.
(4) Attach aftercooler tube and intercooler
(2) Inspect all parts for cracks, breaks or
tube to compressor and air tank.
bends.
(5) Place engine assembly on handtruck and
(3) Inspect all hardwar for damaged threads.
fasten. Do not tighten bolts at this time.
(4) Repair or replace all defective parts.
(6) Connect fuel line to fuel filter.
d. Reassembly of Handtruck.
(7) Install belts and adjust tension to obtain
(1) Attach rails (23, fig. 4-21) and cross-
belt deflection of 0.75 to 1.0 inch (1.91 to 2.54 cm)
members (24) with screws and nuts (22). Attach
midway between pulleys. Tighten engine mounting
bumper and screws (21).
bolts.
(2) Attach LH nose (19) and RH nose (20)
(8) Install belt guard with screw attaching to
with screws (17) and nuts (18). Install axle (16)
compressor and nuts attaching to truck frame.
Section XIII. MAINTENANCE OF ACCESSORY ITEMS
b. Compressor Identification Plate. The com-
4 - 2 7 . Air Discharge Items.
press pump plate specifies the name of the manu-
The adapter hose, hose assembly and air chuck
facturer, the model number, and the serial number
are replaced if found defective upon inspection.
of the pump. The plate is mounted on the end cover
of the pump.
4-28. Data Plates.
c. Engine Identification Plate. The engine
a. End Item Identification Plate. The air
plate indicates the make, model, serial number,
compressor plate specifies the name of the manu-
stock number, and other pertinent maintenance
facturer, model number, date of manufacture, serial
data. The plate is mounted on the flywheel housing.
number and the National stock number. The plate is
d. The data plates are replaced if found
mounted on the left rear of the handtruck.
defective.
MAINTENANCE OF GAGES
Section XIV.
Pressure
Gage
and
Mounting
4-29.General.
Tube.
Among the compressor assembly equipment are
a Removal.
the air pressure gage and the gage mounting tube.
(1) Detach mounting tube (3, fig. 4-22) from
fitting (4).
