TM 5-4310-354-14
KEY to figure 7-16:
1. Wire and seal (3)
42.
Governor arm
82.
Seal
2. Screw (3)
43.
Linkage hook
83.
Ring
3. Lock washer (3)
44.
Metering valve
84.
Spring
4. Flat washer (3)
45.
Spring
85.
Piston
5. Fuel line connector
46.
Arm assy
86.
Seal
6. Cover
47.
Screw assy
87.
Pipe plug
7. Cover gasket
48.
Seal (2)
88.
Rollpin
8. Lock nut (2)
49.
Screw
89.
Thrust plate
9. Contact nut (2)
50.
Washer
90.
Seal
10. Contact washer (2)
51.
Link assy
91.
Liner
11. Insulating washer (2)
52.
Shim
92.
Pump blade (4)
12. Solenoid frame assy
53.
Plug
93.
Spring (2)
13. Insulating tube (2)
54.
Seal
94.
Screw
14. Coil arm assy
55.
Screw
95.
Valve stop
15. Spring
56.
Plug
96.
Spring
16. Spring sleeve
57.
Piston ring
97.
Delivery valve
17. Retaining clip
58.
Seal
98.
Retaining ring
18. Screw
59.
Power piston
99.
Retainer (2)
19. Retainer
60.
Washer (2)
100.
Retaining ring
20. Spring
61.
Plug
101.
Weight retainer assy
21. Lever assy
62.
Seal (2)
102.
Cam ring
22. Arm
63.
Seal (2)
103.
Screw
23. Screw
64.
Spring
104.
Leaf spring
24. Spacer
65.
Spring
105.
Cam roller (2)
25. Throttle shaft assy
66.
Shim (AR)
106.
Roller shoe (2)
26. Screw (2)
67.
Piston
107.
Plunger (2)
27. Nut (2)
68.
Screw (2)
108.
Seal
28. Washer (3)
69.
Screw (2)
109.
Screw (4)
29. Shaft seal (2)
70.
Washer (2)
110.
Washer (8)
30. Shutoff shaft
71.
Thrust sleeve
111.
Head and rotor assy
31. Lever
72.
Weight (6)
112.
Drive shaft
32. Guide stud
73.
Washer
113.
Key
33. Washer
74.
Screw (4)
114.
Shaft seal (2)
34. Spring
75.
Lock washer (4)
115.
Pilot tube seal
35. Guide
76.
Flat washer (4)
116.
Screw (4)
36. Spring
77.
End plate
117.
Timing cover (2)
37. Retainer
78.
Plug assy
118.
Gasket (2)
38. Spring
79.
Sleeve
119.
Screw (2)
39. Nut (2)
80.
Seal
120.
Identification plate
40. Shaft seal (2)
81.
Filter element
121.
Housing assy
41. Pivot shaft
solenoid assembly off of housing (121)
CAUTION
and remove cover gasket (7).
Disassembly of the fuel injection
(2) Disassemble
cover
and
solenoid
pump shall be conducted in a clean
assembly by removing fuel line connection
work area. Use clean tools and clean
(5) from cover (6), remove two each lock
hands. Provide a clean, deep drawn
nuts (8), contact nuts (9), contact washers
pan, in which disassembled parts
(10), and insulating washers (11). Work
may be placed, with rounded corners
the solenoid frame assembly (12) out of
to lessen the chance of dirt pockets.
cover (6) and remove two insulating tubes
Also, have available a similar pan
(13). Disconnect and remove spring (15),
containing clean fuel oil for flushing
spring sleeve (16), and coil arm assembly
disassembled parts.
(14).
(1) Mount the fuel injection pump in a vise
(3) Rotate throttle shaft assembly to full
using a holding fixture such as Roosa
shutoff position (retaining clip (17) in
Master Fixture No. 13363, or equivalent.
horizontal position). Place a suitable tool
Cut and remove three wires and seals (1).
such as Roosa Master No. 13339, or
Remove three screws (2), lock washers
equivalent
(3), and flat washers (4). Lift cover and
7-20
