TM 3-1040-263-34
the pipe nipple (18). Keep the fuel filter, assembly with
4-51. Installation
the engine.
Installation is the reverse of removal (para 4-7) except for
d. Remove the pipe nipple (18).
the following procedures:
e. Remove the engine adapter (21) (para 4-
a. Apply a coat of compressor oil to the
53a(3) through (5).
splined area of the crankshaft adapter (15, fig. 4-18)
f.
Remove the lockwire (22) and the oil plate
prior to installing compressor on engine.
(23).
b. When installing gasoline engine (34) on
g. Remove the exhaust pipe (27) (para 4-
54a(3) and (4)).
18) to between 3 and 4 pound-feet.
h. Remove the pulley (29 (para 4-55a(2) and
c. Inspect exterior of unit for chipped paint and
(3)).
corrosion.
Remove corrosion, prime, and touchup
i.
Remove the left and right-hand brackets
defective areas, using Enamel, semi-gloss, rust-
(31 and 33) (para 4-57a(2) through (4)).
inhibiting, TT--E-485.
j.
Attach starter rope to removed engine.
4-49. Cleaning and Inspection
4-52.
Crankshaft Adapter
a. Clean all metallic parts in drycleaning
solvent.
NOTE
b. Check all parts for defects or damage.
Replace any defective or damaged parts.
If difficulty is encountered in removing
4-50. Reassembly
the crankshaft adapter (15, fig. 4-18),
remove the engine adapter (21). Then,
NOTE
use a bearing puller to remove the
crankshaft adapter (15).
Make one complete wrap of antiseize
a.
Removal.
tape (MIL-T-27730) around each pipe
thread before reassembly.
(1) Remove canvas group (TAM 3-1040-
26312).
a. Service new model 1A08-3 engine (TM 5-
(2) Remove protecting cage (para 3-7).
2805-256-14).
(3) Using crankcase removal instructions
b. Remove original starter flange from new
(para 4-32), remove the compressor.
(4) Remove the adapter screw (10, fig. 4-
engine and retain starter flange bolts (28, fig. 4-18).
c. Mount pulley (29) with the retained bolts.
18), washer (11), and shims (12, 13, and 14).
b. Installation.
d. Tighten starting flange bolts (28); torque to
(1) Position the crankshaft adapter (15) on
between 10 and 12 pound-feet.
the engine crankshaft.
e. Install exhaust pipe (27) (para 4-54b).
(2) Add sufficient shims (12, 13, and 14)
f.
Install oil plate (23) and lockwire (22).
to maintain a 0.015-inch space between the adapter
g. Install engine adapter (21) (para 4-53b).
washer and the end of the engine crankshaft when
h. Install pipe nipple (18).
assembled.
i.
Install engine fuel filter assembly (17) to
(3) Position shims on engine crankshaft.
pipe nipple (18).
(4) Secure crankshaft adapter (15) and
j.
Install elbow (16) to engine fuel filter (17).
shims (12, 13, and 14) with adapter washers (11) and
k. Install crankshaft adapter (15)(para 452b).
adapter screw (10).
(5) Tighten adapter screw (10) (7.5 to 9.1
pound-feet).
(6) Apply compressor oil to the spline of
the crankshaft adapter (15).
(7) Using
installation
instructions (para 4-36), install compressor.
(8) Assemble protecting cage (para 3-7).
4-33