Chapter 1. INTRODUCTION - TM-5-4930-207-120015
Figure 1-1. Lubricating unit, right rear, 3/4 view
Figure 1-2. Lubricating unit, left front, 3/4 view
Section Il. DESCRIPTION AND DATA - TM-5-4930-207-120018
Figure 1-3. Trailer assembly, left front, three-quarter view
Figure 1-4. Trailer assembly left rear, three-quarter view
Identification and Tabulated Data - TM-5-4930-207-120021
Figure 1-5. Trailer schematic wiring diagram
Figure 1-6. Hydraulic brake system schematic diagram.
Figure 1-7. Lubricator schematic wiring diagram.
Chapter 2. INSTALLATION AND OPERATING INSTRUCTIONS - TM-5-4930-207-120025
Figure 2-2. Trailer operating instructions.
Inspecting and Servicing Equipment
Installation or Setting Up Instructions - TM-5-4930-207-120028
Figure 2-4. Control and instruments (sheet 1 of 4).
Figure 2-4. Controls and instrument is (sheet 2 of 4)
Figure 2-4. Controls and instrument is (sheet 3 of 4)
Section IV. OPERATION UNDER USUAL CONDITIONS - TM-5-4930-207-120032
Figure 2-5. Starting the engine
Fiqure 2-6. Stopping the engine.
Figure 2-7. Transfer pump operation.
Preparing Lubricant Pumps for Operation
Figure 2-8. Preparing lubricant pumps for operation (sheet 2 of 3)
Figure 2-8. Preparing lubricant pumps for operation (sheet 3 of 3)
Dispensing Lubricant
Figure 2-9. Dispensing general purpose grease
Figure 2-10. Dispensing gear oil
Figure 2-11. Dispensing engine oil
Figure 2-12. Lower drawer and accessories.
Figure 2-13. Shutting down the lubricating unit.
Section V. OPERATION UNDER UNUSUAL CONDITIONS - TM-5-4930-207-120045
Table 2-1. Alcohol Dispenser Valve Setting)/g
Section VI. OPERATION OF MATERIAL USED IN CONJUNCTION WITH THE EQUIPMENT
Oil Spray Gun
Figure 2-16. Portable lubricator assembly.
Fire Extinguisher - TM-5-4930-207-120050
Chapter 3. OPERATOR'S MAINTENANCE INSTRUCTIONS - TM-5-4930-207-120051
Table 3-1. Preventive Maintenance Checks and Services (Operator and Crew)
Table 3-2. Operator and Crew Troubleshooting
Section V. OPERATOR'S MAINTENANCE
Figure 3-2. Generator drive belt adjustment.
Figure 3-3. Compressor drive belt adjustment.
Figure 3-4. Compressor air cleaner service.
Figure 3-5. Trailer air brake filter and reservoir service.
Chapter 4. ORGANIZATIONAL MAINTENANCE INSTRUCTIONS - TM-5-4930-207-120059
Section Il. ORGANIZATIONAL MAINTENANCE TROUBLESHOOTING
Table 4-2. Organizational Troubleshooting - TM-5-4930-207-120061
Section Ill. ENCLOSURE ASSEMBLY, BATTERY AND ACCESSORY DRAWERS, AND TOOL BOX
Figure 4-2. Tool box and accessory drawer, removal and installation.
Section IV. ELECTRICAL SYSTEM
Figure 4-4. Generator and voltage regulator, removal and installation.
Figure - TM-5-4930-207-120066
Figure 4-6. OiI pressure transmitter and oil pressure switches, removal and installation.
Figure 4-7. Gages, control panel, gages, and switches, emoval and installation.
Trailer Clearance Lights and Lamps
Figure 4-9. Trailer clearance lights, disassembly and reassembly.
Figure 4-10. Reflectors, blackout-stoplight, taillights, lamps and wiring harness, removal and installation (sheet 2 of 2).
Figure 4-11. Taillight and blacknut-stoplight, disassemble and reassembly.
Section V. FUEL AND EXHAUST SYSTEM
Figure 4-13. Fuel tank, removal and installation.
Figure 4-14. Exhaust diverter valve, removal and installation.
Section VI. COMPRESSOR ASSEMBLY AND AIR LINES
Figure 4-15. Compressor drive pulley, removal and installation
Figure 4-16. Air compressor, removal and installation.
Air Relief Valve
Section VII. AIR LUBRICATION SYSTEM
Figure 4-18. Air regulator valve, removal and installation.
Figure 4-19. Air regulator, dissaernbly and reassembly
Figure 4-20 Lubricant pump, removal and installation.
Figure 4-21. Lubricant tank cover, removal and installation.
Figure 4-22. Lubricant calves and meters, removal nad installation
Lubricant and Air Hoses
Figure 4-23. Lubricant and air hoses, removal nad installation
Hose Reel Assembly
Figure 4-24. Hose assembly, removal and installation.
Figure 4-25. Hose reel bank, removal and installation.
Figure. 4-26. Alcohol dispenser, removal and installation.
Figure 4-27. Alcohol dispesner, disassembly and reassembly.
Section Vlll. ENGINE AND CLUTCH
Figure 4-28. Engine and clutch, removal and installation.
Section IX. TRAILER WHEELS AND BRAKES
Figure 4-29. Wheel and tire, removal and installation
Wheel Hub and Brake Drum
Figure 4-30. Wheel hub and brake drum, removal, disassmebly, reassembly and installation
Service Brakes Adjustment and Bleeding
Wheel Cylinders and Brake Shoes
Figure 4-32. Wheel cylinder and brake shoe, removal and installation (sheet 1 of 2)
Figure 4-32. Wheel cylinder and brake shoe, removal and installation (sheet 2 of 2)
Figure 4-33 Hydraulic master cylinder, brake chamber and relay valve, removal and installation.
Brake Relay Emergency Valve
Section X. TRAILER FRAME
Figure 4-36. Landing gear and lunette, removal and installation.
Figure 4-37. Landing gear, disassembly and reassembly
Figure 4-38. Trailer suspenion system and wheel chocks, removal and installation (sheet 1 of 2).
Figure 4-38. Trailer suspension system and wheel chocks, removal and installation(sheet 2 of 2).
Figure 4-39. Fender, removal and installation.
Figure 4-40. Safety chain, removal and installation
Appendix A. REFERENCES - TM-5-4930-207-120112
Appendix B. MAINTENANCE ALLOCATION CHART - TM-5-4930-207-120113
Section Il. MAINTENANCE ALLOCATION CHART - TM-5-4930-207-120114
Section Ill. SPECIAL TOOL AND SPECIAL TEST EQUIPMENT REQUIREMENTS
Section IV. REMARKS - TM-5-4930-207-120116
Appendix C. BASIC ISSUE ITEMS LIST - TM-5-4930-207-120117
Section Il. BASIC ISSUE ITEMS
Section III. Maintenance and Operating Supplies - TM-5-4930-207-120119
TM-5-4930-207-12 Lubricating and Servicing Unit Power Operated Trailer Mounted 23 CFM Compressor Reciprocating Gasoline Driven (Henry Spen Model 901765-1) Manual
Figure 1-1. Lubricating unit, right rear, 3/4 view
Figure 1-2. Lubricating unit, left front, 3/4 view
Section Il. DESCRIPTION AND DATA - TM-5-4930-207-120018
Figure 1-3. Trailer assembly, left front, three-quarter view
Figure 1-4. Trailer assembly left rear, three-quarter view
Identification and Tabulated Data - TM-5-4930-207-120021
Figure 1-5. Trailer schematic wiring diagram
Figure 1-6. Hydraulic brake system schematic diagram.
Figure 1-7. Lubricator schematic wiring diagram.
Chapter 2. INSTALLATION AND OPERATING INSTRUCTIONS - TM-5-4930-207-120025
Figure 2-2. Trailer operating instructions.
Inspecting and Servicing Equipment
Installation or Setting Up Instructions - TM-5-4930-207-120028
Figure 2-4. Control and instruments (sheet 1 of 4).
Figure 2-4. Controls and instrument is (sheet 2 of 4)
Figure 2-4. Controls and instrument is (sheet 3 of 4)
Section IV. OPERATION UNDER USUAL CONDITIONS - TM-5-4930-207-120032
Figure 2-5. Starting the engine
Fiqure 2-6. Stopping the engine.
Figure 2-7. Transfer pump operation.
Preparing Lubricant Pumps for Operation
Figure 2-8. Preparing lubricant pumps for operation (sheet 2 of 3)
Figure 2-8. Preparing lubricant pumps for operation (sheet 3 of 3)
Dispensing Lubricant
Figure 2-9. Dispensing general purpose grease
Figure 2-10. Dispensing gear oil
Figure 2-11. Dispensing engine oil
Figure 2-12. Lower drawer and accessories.
Figure 2-13. Shutting down the lubricating unit.
Section V. OPERATION UNDER UNUSUAL CONDITIONS - TM-5-4930-207-120045
Table 2-1. Alcohol Dispenser Valve Setting)/g
Section VI. OPERATION OF MATERIAL USED IN CONJUNCTION WITH THE EQUIPMENT
Oil Spray Gun
Figure 2-16. Portable lubricator assembly.
Fire Extinguisher - TM-5-4930-207-120050
Chapter 3. OPERATOR'S MAINTENANCE INSTRUCTIONS - TM-5-4930-207-120051
Table 3-1. Preventive Maintenance Checks and Services (Operator and Crew)
Table 3-2. Operator and Crew Troubleshooting
Section V. OPERATOR'S MAINTENANCE
Figure 3-2. Generator drive belt adjustment.
Figure 3-3. Compressor drive belt adjustment.
Figure 3-4. Compressor air cleaner service.
Figure 3-5. Trailer air brake filter and reservoir service.
Chapter 4. ORGANIZATIONAL MAINTENANCE INSTRUCTIONS - TM-5-4930-207-120059
Section Il. ORGANIZATIONAL MAINTENANCE TROUBLESHOOTING
Table 4-2. Organizational Troubleshooting - TM-5-4930-207-120061
Section Ill. ENCLOSURE ASSEMBLY, BATTERY AND ACCESSORY DRAWERS, AND TOOL BOX
Figure 4-2. Tool box and accessory drawer, removal and installation.
Section IV. ELECTRICAL SYSTEM
Figure 4-4. Generator and voltage regulator, removal and installation.
Figure - TM-5-4930-207-120066
Figure 4-6. OiI pressure transmitter and oil pressure switches, removal and installation.
Figure 4-7. Gages, control panel, gages, and switches, emoval and installation.
Trailer Clearance Lights and Lamps
Figure 4-9. Trailer clearance lights, disassembly and reassembly.
Figure 4-10. Reflectors, blackout-stoplight, taillights, lamps and wiring harness, removal and installation (sheet 2 of 2).
Figure 4-11. Taillight and blacknut-stoplight, disassemble and reassembly.
Section V. FUEL AND EXHAUST SYSTEM
Figure 4-13. Fuel tank, removal and installation.
Figure 4-14. Exhaust diverter valve, removal and installation.
Section VI. COMPRESSOR ASSEMBLY AND AIR LINES
Figure 4-15. Compressor drive pulley, removal and installation
Figure 4-16. Air compressor, removal and installation.
Air Relief Valve
Section VII. AIR LUBRICATION SYSTEM
Figure 4-18. Air regulator valve, removal and installation.
Figure 4-19. Air regulator, dissaernbly and reassembly
Figure 4-20 Lubricant pump, removal and installation.
Figure 4-21. Lubricant tank cover, removal and installation.
Figure 4-22. Lubricant calves and meters, removal nad installation
Lubricant and Air Hoses
Figure 4-23. Lubricant and air hoses, removal nad installation
Hose Reel Assembly
Figure 4-24. Hose assembly, removal and installation.
Figure 4-25. Hose reel bank, removal and installation.
Figure. 4-26. Alcohol dispenser, removal and installation.
Figure 4-27. Alcohol dispesner, disassembly and reassembly.
Section Vlll. ENGINE AND CLUTCH
Figure 4-28. Engine and clutch, removal and installation.
Section IX. TRAILER WHEELS AND BRAKES
Figure 4-29. Wheel and tire, removal and installation
Wheel Hub and Brake Drum
Figure 4-30. Wheel hub and brake drum, removal, disassmebly, reassembly and installation
Service Brakes Adjustment and Bleeding
Wheel Cylinders and Brake Shoes
Figure 4-32. Wheel cylinder and brake shoe, removal and installation (sheet 1 of 2)
Figure 4-32. Wheel cylinder and brake shoe, removal and installation (sheet 2 of 2)
Figure 4-33 Hydraulic master cylinder, brake chamber and relay valve, removal and installation.
Brake Relay Emergency Valve
Section X. TRAILER FRAME
Figure 4-36. Landing gear and lunette, removal and installation.
Figure 4-37. Landing gear, disassembly and reassembly
Figure 4-38. Trailer suspenion system and wheel chocks, removal and installation (sheet 1 of 2).
Figure 4-38. Trailer suspension system and wheel chocks, removal and installation(sheet 2 of 2).
Figure 4-39. Fender, removal and installation.
Figure 4-40. Safety chain, removal and installation
Appendix A. REFERENCES - TM-5-4930-207-120112
Appendix B. MAINTENANCE ALLOCATION CHART - TM-5-4930-207-120113
Section Il. MAINTENANCE ALLOCATION CHART - TM-5-4930-207-120114
Section Ill. SPECIAL TOOL AND SPECIAL TEST EQUIPMENT REQUIREMENTS
Section IV. REMARKS - TM-5-4930-207-120116
Appendix C. BASIC ISSUE ITEMS LIST - TM-5-4930-207-120117
Section Il. BASIC ISSUE ITEMS
Section III. Maintenance and Operating Supplies - TM-5-4930-207-120119
TM-5-4930-207-12 Lubricating and Servicing Unit Power Operated Trailer Mounted 23 CFM Compressor Reciprocating Gasoline Driven (Henry Spen Model 901765-1) Manual
